Easyfit+ waterproof fixtures
The Interlight Easyfit+ waterproof fixtures have been renewed! They are now supplied as standard with 5 x 2.5mm² feed-through wiring with handy plug-in terminals on both sides. Super fast installation and interconnection!



With swivel and blind plug
The Easyfit+ surface-mounted fixtures are waterproof and fully protected against dust (IP66). The fixture is easy to open with the stainless steel locking clips. To make it easier for the installer, the locking clips stay up and the shade is easy to open or replace. The locking clips can be fitted with locking screws so that the fixture cannot be opened without tools
The fixture is made of PC, polycarbonate. This material is UV resistant, fire retardant and has high impact resistance (IK08).
Leds
Thanks to the high-quality chips, the efficiency of this fixture is >140 lumens per watt at the 60cm and even >150 lumens per watt in the 120 and 150cm. The LEDs are integrated into the hood of the fixture. When the fixture is opened, the LEDs are not visible. The upper box where the LEDs are located is attached to the lower box with 2 tie-rips. When installed on the ceiling there is enough space for installation.


stainless steel locking clips
The Easyfit+ surface-mounted fixtures are waterproof and fully protected against dust (IP66). The fixture is easy to open with the stainless steel locking clips. To make it easier for the installer, the locking clips stay up and the shade is easy to open or replace. The locking clips can be fitted with locking screws so that the fixture cannot be opened without tools
The fixture is made of PC, polycarbonate. This material is UV resistant, fire retardant and has high impact resistance (IK08).
Connection terminals and 5×2.5mm2 conduit wiring
Thanks to the simple connection terminals, the fixture is quickly connected. The fixture comes standard with conduit wiring 5×2.5mm2 with connectors with plug-in terminals on both sides, so you can easily and quickly connect the power cable. Thereby, a swivel is already mounted on one side. On the other side is a swivel blind plug that can be replaced in seconds with the supplied second swivel. The fixture is equipped with an M20 gland with standard capability for a connecting cable of 8-12mm. In the accessory bag is a larger silicone rubber which can be replaced in the gland for a connection cable of 12-14mm.


Adjustable driver
The fixture is equipped with an Interlight X5 driver which can be set to four positions with dipswitches. The driver defaults to 350 milliamps and can be switched back to 200 milliamps to reduce the lumen output.
With sensor
The sensor can be set as desired by dip switches. For example, the detection range can be set to 100% or 50%, the lag time from 5 seconds to 30 minutes, the daylight threshold from 30 lux to 200 lux. The sensor can also be set to keep the fixture on at 10% or 30% with a standby period of 3 minutes to always.


With emergency module
The fixture has an integrated emergency module which can be set in three ways. Thus it can be used as a switchable fixture, as a fixture which is always on or as a fixture which is always off. Of course, it is also possible to order the fixture with sensor and emergency module.
The emergency module is available in 120 and 150 cm. In these sizes it is also possible to order the Easyfit+ fixtures with sensor and emergency module.
The advantages of Easyfit+ waterproof fixtures
Summarized:
- With swivel and blind plug
- Sustainable; no plastic packaging
- stainless steel locking clips
- With through-wiring 5 x 2,5mm²
- Adjustable Lumen Output
- >150 lumens per watt
- Leds integrated into the hood
With sensor
Watch the video
Our Easyfit+ waterproof range
On/Off
With sensor
With emergency lighting
With sensor and emergency lighting
We look forward to hearing about your issue!
Rody, Michel, Kees, Peter and Richard are always there for you! They are happy to help you choose the right products, create lighting plans and provide demos.
Or send an email using our contact form











